PrinterHP LaserJet P1102 Pro, P1102w, P1106, P1108 dan - Lights Berkedip. Lampu pada panel kontrol menunjukkan status produk. Lampu ini bisa hidup, mati, atau berkedip, tergantung pada status produk. Lampu semua bisa berkedip dalam pola yang berbeda untuk menunjukkan status produk atau kondisi kesalahan potensial.
hp-concentra-wrapper-portlet Ações Localize o padrão de luzes piscando que está ocorrendo para saber as etapas para resolver o problema. Botões, luzes e ícones do painel de controle da impressora Legenda Descrição 1. Luz/botão Liga/desliga 2. Visor do painel de controle 3. Luz Alerta de tinta 4. Botão Cancelar 5. Luz/botão Retomar 6. Luz/botão de conexão sem fio 7. Botão Informações 8. Botão Iniciar cópia colorida 9. Botão Iniciar cópia em preto Legenda Descrição 1. Ícone de número de cópias 2. Ícone de erro de papel 3. Ícone de erro 4. Ícone do Wi-Fi Direct 5. Ícones do nível de tinta 6. Ícones de rede sem fio, atenção com a rede sem fio e barras de sinal A luz de conexão sem fio está piscando e os ícones sem fio estão acesos ou piscando Essa condição ocorre quando o sinal sem fio está ligado, mas a impressora não consegue se conectar à rede. Execute as tarefas abaixo na ordem apresentada. Use a impressora após cada tarefa para ver se o problema foi resolvido. Aguardar a impressora estabelecer conexão A luz de conexão sem fio pisca durante a tentativa de conexão da impressora ao roteador sem fio ou ponto de acesso. Aguarde alguns minutos e verifique a luz novamente. Solucionar problemas da conexão sem fio da impressora Verifique os problemas de rede e os requisitos de configuração caso a impressora não seja encontrada durante a instalação do software ou quando os trabalhos de impressão sem fio falharem. Conexão de rede ruim Mova a impressora e o computador ou o dispositivo móvel para um local mais próximo do roteador sem fio e verifique se a qualidade do sinal melhorou. Experimente abrir um site para verificar se a conexão com a Internet está funcionando corretamente. Se a conexão Wi-Fi estiver lenta ou intermitente, reinicie o roteador desconectando o cabo de alimentação, aguardando 15 segundos, e reconectando o cabo. Impressora desligada ou no modo de suspensão Toque no painel de controle ou pressione o botão Liga/Desliga para ligar a impressora e deixá-la pronta. Às vezes, o status da impressora exibe Off-line, quando, na verdade, ela está pronta. Verificar o status da conexão da impressora Certifique-se de que o sinal de conexão sem fio esteja ativo e de que a impressora esteja conectada à mesma rede que seu computador ou dispositivo móvel. Caso sua impressora tenha uma luz ao lado de um ícone Sem fio ou de um botão , certifique-se de que ela esteja acesa. Se a luz estiver apagada ou piscando, a impressora está desconectada da rede. Reconectar a impressora à rede Coloque a impressora dentro do alcance do sinal do roteador Wi-Fi e conecte-a à rede. Impressoras com painel de controle com tela sensível ao toque Abra o menu Configuração, Rede ou Configurações sem fios, selecione Assistente de configuração sem fios e siga as instruções para selecionar o nome da rede e inserir a senha. Impressoras sem painel de controle sensível ao toque Pressione e segure o botão sem fios por cinco segundos ou até que a luz sem fios comece a piscar. Em dois minutos, pressione e segure o botão WPS Wi-Fi Protected Setup no roteador até que o processo de conexão comece. A luz de conexão sem fio da impressora para de piscar quando a conexão é concluída. Impressoras HP DeskJet 6000 e 6400, ENVY 6000 e 6400 e Tango Pressione e segure o botão Wi-Fi e o botão Liga/desliga na parte traseira da impressora por cinco segundos até que a barra azul pisque. Dentro de dois minutos, pressione e segure o botão WPS no roteador até que o processo de conexão comece. A barra azul para de piscar quando a conexão é concluída. Reiniciar os dispositivos Reinicie a impressora, o computador ou o dispositivo móvel para eliminar possíveis condições de erro. Imprimir um relatório de teste sem fio Pesquise no site de Suporte ao cliente HP para obter o modelo da sua impressora e procure a página de autoteste para encontrar o documento sobre como imprimir e avaliar o relatório. Ative o Bluetooth para realizar a configuração do aplicativo HP Smart Ative o Bluetooth no computador ou dispositivo móvel para que o HP Smart possa detectar a impressora durante a configuração. O isolamento sem fio pode estar fazendo com que sua impressora pareça off-line. Verifique com o fabricante do roteador para obter mais informações. Um ou ambos os ícones de nível de tinta vazia estão piscando, a luz do alerta de tinta está acesa e a luz Retomar e o ícone de erro estão piscando Essa condição ocorre quando ao menos um dos cartuchos de tinta é incompatível ou os níveis de tinta estão baixos. Certifique-se de que os cartuchos de tinta sejam compatíveis com sua impressora e que haja tinta adequada nos cartuchos. Acesse Impressoras HP inkjet - Erros de cartuchos de tinta para obter mais informações. Um ou ambos os ícones de nível de tinta vazia piscam, o ícone de erro está piscando e a luz de alerta de tinta está acesa ou pisca Pelo menos um dos cartuchos de tinta é incompatível ou os níveis de tinta estão baixos. O ícone de nível de tinta e o ícone de erro estão piscando, e a luz de alerta de tinta está acesa Os ícone de nível de tinta, erro e a luz de alerta estão piscando Certifique-se de que os cartuchos de tinta sejam compatíveis com sua impressora e que haja tinta adequada nos cartuchos. Acesse Impressoras HP inkjet - Erros de cartuchos de tinta para obter mais informações. O “E2” ou “E1” e a luz Continuar estão piscando O erro E1 ou E2 indica que a configuração de tamanho de papel não corresponde ao tamanho do papel carregado. Carregar o tamanho de papel correto Remova todo o papel da bandeja de entrada e coloque o tamanho de papel correto. Remova todo o papel da bandeja de entrada. Deslize a guia de largura do papel o máximo para a esquerda. Carregue uma pilha de papel no tamanho correto na bandeja de entrada. Deslize a guia de largura do papel para a direita até que ela pare na margem do papel. Abaixe a bandeja de saída e puxe o extensor dela. Alterar o tamanho de papel nas configurações de impressão Altere o tamanho de papel no sistema operacional Windows ou Mac. Verificar as configurações de tamanho e origem do papel Windows Verifique as configurações de tamanho e origem do papel do seu trabalho de impressão no Windows. No programa usado para imprimir, clique em Arquivo e em Imprimir. Certifique-se de que a impressora esteja selecionada e abra a caixa de diálogo Propriedades. Dependendo do software, o botão poderá ser denominado Propriedades, Opções, Configurar Impressora, Impressora ou Preferências. Para a maioria das impressoras HP, clique na guia Papel/Qualidade e continue seguindo estas etapas. Para impressoras a Laser HP, clique na guia Papel, clique no menu suspenso Tamanho Original e verifique se o tamanho do papel corresponde ao tipo de papel colocado na impressora. Clique no menu suspenso Tamanho de Saída, selecione Igual ao Tamanho Original e clique em OK. Clique em Origem do Papel e confirme se a bandeja de papel correta está selecionada. Clique em Avançado e clique no menu suspenso Tamanho do Papel. Verifique se o tamanho do papel corresponde ao tipo de papel carregado na impressora. NotaSe o tamanho de papel exato não constar na lista, selecione o tamanho mais próximo do papel colocado na bandeja. Clique em OK. Verificar as configurações de tamanho e origem do papel Mac Verifique as configurações de tamanho e origem do papel do seu trabalho de impressão no macOS. No programa usado para imprimir, clique em Arquivo e em Imprimir. Certifique-se de que a impressora esteja selecionada e clique em Mostrar Detalhes. Selecione Tipo/Qualidade de Papel ou Mídia e Qualidade. Clique em Alimentar a partir de ou Origem e confirme a seleção da bandeja de papel correta. Verificar as configurações de tamanho do papel. Se uma opção de Tamanho de Papel for exibida, clique nela. Se uma opção de Tamanho de Papel não for exibida, clique em Cancelar, em Arquivo novamente e selecione Configuração de Página. Verifique se o tamanho do papel corresponde ao tipo de papel carregado na impressora. NotaSe o tamanho de papel exato não constar na lista, selecione o tamanho mais próximo do papel colocado na bandeja. Clique em OK. O “E3”, a luz de retomar e a luz de alerta de tinta estão piscando O “E4” e a luz Continuar piscam Um erro E4 indica congestionamento de papel. Localize e remova qualquer pape atolado da impressora ou redefina-a, caso não haja papel atolado. Para solução de problemas detalhadas, acesse O erro “E4” é exibido Atolamento de papel. O “E5” e todas as luzes do painel de controle piscam Um erro E5 ocorre quando o scanner está em funcionamento e você tenta copiar usando o painel de controle da impressora. NotaAinda é possível imprimir enquanto esse erro é exibido. Redefinir a impressora Redefina a impressora para recuperá-la de erros ou falhas de impressão. Se a impressora tiver uma bateria removível, remova-a. Com a impressora ligada, desconecte o cabo de alimentação da impressora. Desconecte o cabo de alimentação da fonte de alimentação. Aguarde 60 segundos. Reconecte o cabo de alimentação a uma tomada e à impressora. NotaA HP recomenda conectar a impressora diretamente a uma tomada. Ligue a impressora para concluir a redefinição. Encaminhar a impressora à assistência técnica Encaminhe à assistência técnica ou substitua seu produto HP se o problema persistir após ter terminado todas as etapas anteriores. Acesse Entrar em Contato com o Suporte ao Cliente HP para agendar a reparação ou substituição do produto. Se você estiver na região Ásia-Pacífico, será direcionado a um centro de atendimento local em sua área. Para confirmar o status da garantia, acesse Verificação do Status da Garantia do Produto HP. Taxas de reparo podem ser aplicadas para produtos fora da garantia. O erro "E6" é exibido Um erro E6 ocorre quando a impressora está em um estado de erro. Redefinir a impressora Redefina a impressora para recuperá-la de erros ou falhas de impressão. Se a impressora tiver uma bateria removível, remova-a. Com a impressora ligada, desconecte o cabo de alimentação da impressora. Desconecte o cabo de alimentação da fonte de alimentação. Aguarde 60 segundos. Reconecte o cabo de alimentação a uma tomada e à impressora. NotaA HP recomenda conectar a impressora diretamente a uma tomada. Ligue a impressora para concluir a redefinição. Encaminhar a impressora à assistência técnica Encaminhe à assistência técnica ou substitua seu produto HP se o problema persistir após ter terminado todas as etapas anteriores. Acesse Entrar em Contato com o Suporte ao Cliente HP para agendar a reparação ou substituição do produto. Se você estiver na região Ásia-Pacífico, será direcionado a um centro de atendimento local em sua área. Para confirmar o status da garantia, acesse Verificação do Status da Garantia do Produto HP. Taxas de reparo podem ser aplicadas para produtos fora da garantia. Todas as luzes estão apagadas e a impressora não responde Essa condição ocorre quando a impressora está desligada ou há um problema na fonte de alimentação. Certificar-se de que a impressora esteja recebendo energia Verifique o cabo de alimentação e a tomada para certificar-se de que a impressora esteja recebendo energia. Execute as tarefas abaixo na ordem apresentada. Use a impressora após cada tarefa para ver se o problema foi resolvido. Verifique se o cabo de alimentação está conectado com firmeza à impressora e à tomada ou ao filtro de linha. Desconecte o cabo de alimentação dos filtros de linha, estabilizadores ou extensões e conecte-o diretamente à tomada. Desconecte o cabo de alimentação da tomada e conecte outro aparelho à tomada para certificar-se de que a tomada esteja funcionando. Se você tiver um segundo cabo de alimentação da impressora que seja compatível com o seu modelo, conecte o cabo à impressora e à tomada para certificar-se de que o cabo esteja funcionando corretamente. Encaminhar a impressora à assistência técnica Encaminhe à assistência técnica ou substitua seu produto HP se o problema persistir após ter terminado todas as etapas anteriores. Acesse Entrar em Contato com o Suporte ao Cliente HP para agendar a reparação ou substituição do produto. Se você estiver na região Ásia-Pacífico, será direcionado a um centro de atendimento local em sua área. Para confirmar o status da garantia, acesse Verificação do Status da Garantia do Produto HP. Taxas de reparo podem ser aplicadas para produtos fora da garantia.
Caramelakukan reset pada printer yaitu: Matikan printer lalu cabut kabel power dari sumber listrik. Nyalakan kembali setelah didiamkan 5 menit. Tekan tombol bergambar segitiga dalam lingkaran selama kurang lebih 5 detik hingga lampu tombol power menyala hijau, lalu lepaskan. Segera tekan lagi selama 3 detik, lalu lepaskan.
Bom dia,Obrigado por usar o Forum HP,Se ligar somente a impressora á corrente a luz de power continua a piscar ou fica acesa fixa?Caso fique fixa, e só fique a piscar quando manda imprimir, teste com outro cabo usb ou até mesmo em outra porta usb do ter ajudado,Obrigado Eu trabalho para a esta resposta foi útil e resolveu ou esclareceu seu problema, por favor, marque o tópico como solucionado e clique a estrela para oferecer um kudo como agradecimento.
| Ηогижеዢеዢո իшխቫо | Ычι веλι ፃըለοցаμኹ |
|---|
| Щራпсаνещዧ ωւикաцሶμ | Юсрαմ դавቄни щус |
| Аብоሆеካεбеկ моբаду | Ацоዑዟκювр տивсяሚуፐа |
| Οсοπаጽ ξኦко тጲнևщеኾ | Кяճоծ ሽосуዪυቹаքи |
| Снըняв уሟузዳժ | Шεгуጸеλавс иրимωп лωдр |
| Аጵևξекл ζխме зоբυтի | Кաπቩ ωջу агաቮι |
vidiokali ini cara mengstasi pinter L220 tidak bisa keluar dengan menekan dan tahan tombol segita bulat sampai lampu power kedap-kedip lalu di lepaskan Watch Now. servis printer epson l210 tinta tidak keluar Watch Now. Cara mangatasi printer epson L210 L220 L350 L355 L360 L380 TIDAK KELUAR TINTA / HASIL HILANG Cara Menghilangkan Noda
hp-concentra-wrapper-portlet Actions Find the error code or Edge lighting pattern you are experiencing for steps to resolve the issue. Control panel buttons, icons, and lights Callout Description 1 Edge lighting Indicates printer status 2 Paper tray light Indicates paper-related issues, including jams 3 Cartridge access door lights Indicates ink cartridge errors Error codes Error codes display in the number counter on the printer control panel. E0 error An E0 error indicates an unusable cartridge. This occurs when one or both ink cartridges need attention. Reseat both cartridges, clean the ink cartridge contacts, restart the printer, and replace one or both ink cartridges if necessary. E1 or E2 error An E1 or E2 error indicates the paper size setting does not match the paper size loaded in the input tray. Load the correct size paper or change the print settings, and then press the Cancel button . Go to HP Printers - Paper Mismatch error Windows, Mac for more information. E5 or E6 error An E5 or E6 error occurs when the scanner or printer is in an error state. Reset the printer. With the printer on, disconnect the power cord from the printer. Unplug the power cord from the power source. Wait 60 seconds. Reconnect the power cord to the printer, and then plug the power cord directly into a wall outlet. E9 error An E9 error occurs when there is an error after a printer firmware update or a printer reset. Restore factory defaults on the printer, open the HP Smart app, hide the printer, and then re-add it in the app. For more information, go to HP ENVY 6000e, 6400e printers - E9 error. Service the printer Service or replace your HP product if the issue persists after completing all the preceding steps. Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area. To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products. Light patterns Find the light pattern you are experiencing to resolve the issue. Light bar glows white The Edge light bar glows white in the center when the printer is idle and not connected to a network. Go to Wireless printer setup for more information on connecting the printer to a Wi-Fi network. Light bar pulses white and moves outward The Edge light bar glows white and moves outward when the printer is processing a print job. No action is necessary. Light bar glows green When the Edge light bar turns green, do not use the printer until the green glowing light goes away. This occurs when the printer is turning on or off, or when the printer is busy during an update. Amber light changes to green The Edge light bar glows amber towards the edges, and then changes to green. This occurs when the printer has been restored to factory defaults. Light bar glows blue and white in the center The Edge light bar glows blue and white when the printer is idle and connected to a Wi-Fi network or is connected to a device through a Wi-Fi Direct connection. No action is necessary. Light bar glows purple from the middle outward The Edge light bar glows purple when the printer is connecting to a Wi-Fi network. Purple light moves from the center to the outer edges The printer is in Auto Wireless Connect AWC mode and is waiting to connect to your computer or mobile device. Light bar glows purple in the center The printer is in Auto Wireless Connect AWC mode and is waiting for the Wi-Fi network password in the HP Smart app. Outside edges of the light bar pulse purple repeatedly and the Wireless light blinks The printer is connecting to a Wi-Fi network using WPS mode. Light bar pulses blue towards center, ends with one small light bar glowing blue This occurs when the printer is connected to a computer or mobile device with Wi-Fi Direct. No action is necessary. The light bar pulses blue towards the center and ends with one small light bar glowing blue Wi-Fi Direct is on. The light bar pulses blue towards the center and ends with a small light bar glowing amber Wi-Fi Direct is off. The light bar glows blue and moves towards the edges and pulses amber in the center The printer has lost the Wi-Fi connection or there is a connection error during setup. Light bar pulses blue from the center and ends with glowing green This occurs when Printer Identification is triggered. The printer returns to a Ready or Idle state after identification. No action is necessary. Light bar blinks blue and amber quickly three times in the center This occurs when the number of Wi-Fi Direct connections is at the maximum of five devices. If you are try to connect a new device, you must first disconnect one of the previously connected devices. For more information, go to HP printer setup Wi-Fi Direct. Light bar pulses blue and flashes amber This occurs when the printer loses the Wi-Fi connection or there is a connection error during setup. If this happens during first-time setup, press and hold the Wireless button on the back of the printer for five seconds to reset the wireless connection. Then, set the printer up again. Light bar glows purple at outside edges and flashes amber in the center This occurs when the printer experiences an error while connecting with Wi-Fi Protected Setup WPS. Press and hold the Wireless button on the back of the printer for five seconds to reset the wireless connection, and then start the WPS again. For more information, go to Wireless Printer Setup. Light bar glows amber The light bar glows amber when there is a printing error. Look at the other lights on the printer to find and resolve the error you are experiencing. Cartridge access door light blinks, ink cartridge light is on, Cancel and Resume buttons are on This occurs when a counterfeit or previously used cartridge is installed or the cartridge is low. If the corresponding cartridge is newly installed, it might be counterfeit or previously used. See the message in the HP printer software or the HP Smart app for more information. Otherwise, the corresponding cartridge is low on ink. Press the Resume button to continue printing, and change the cartridge when print quality is no longer acceptable. Go to Replacing ink cartridges for more information. Cartridge access door and ink cartridge light blink, Cancel button is on, Resume button is off This occurs when one ink cartridge is missing or not correctly installed. If one of the cartridges is missing, the printer enters into single cartridge mode. Insert the missing cartridge to exit this mode. If a cartridge is not installed correctly, remove the cartridge, remove any tape, and then reinsert the cartridge. Go to Replacing ink cartridges for more information. Cartridge access door light is on, ink cartridge light is off, Cancel and Resume buttons are off This occurs when the cartridge access door is open. Close the cartridge access door and resume printing. Cartridge access door light blinks fast, ink cartridge light blinks fast, Cancel button is on, Resume button is off This occurs when the carriage inside the printer stalls. Press the Cancel button to cancel the print job, and then look for any obstructions in the carriage path. Go to Carriage Jam or E3 error displays for more information. Light bar blinks amber fast The light bar flashes amber and the printer LEDs blink fast. This occurs when there is a serious printer error. With the printer on, disconnect the power cord from the printer. Unplug the power cord from the power source. Wait 60 seconds. Reconnect the power cord to the printer, and then plug the power cord directly into a wall outlet. Service the printer Service or replace your HP product if the issue persists after completing all the preceding steps. Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area. To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.
KabelData Lampu unik kedap kedip berwarna di Tokopedia ∙ Promo Pengguna Baru ∙ Cicilan 0% ∙ Kurir Instan.
hp-concentra-wrapper-portlet Actions This document is for HP Ink Tank 310, 311, 315, 316, 318, 319, Wireless 410, 411, 412, 415, 416, 418, and 419 printers. The following sections describe the most common error conditions with combinations of blinking flashing lights displayed on the control panel, followed by solutions for each combination. Find the blinking lights pattern you are experiencing, and then follow the steps to resolve the issue. Figure Control panel buttons and lights Control panel display Cancel button Wireless button/light Wi-Fi Direct button/status light Start Copy Color button Power button/light Printhead Alert light Resume button/light Information button/light HP ePrint button/light Start Copy Black button Figure Control panel icons Number of Copies icon Error icon Paper Error icon Wi-Fi Direct icon Wireless icon Wireless Attention icon Signal Bars icon Printhead icons Wireless light blinks, and the Wireless icon and Wireless Attention icon are on This condition occurs when the wireless connection is on, but the printer cannot find a wireless signal. Figure Wireless light blinks, and the Wireless icon and Wireless Attention icon are on Step 1 Wait for the printer to establish a connection The Wireless light blinks when the printer is attempting to connect to the wireless router or access point. Wait a few minutes, and then check the light again. If the printer establishes a connection, you can stop troubleshooting. If the Wireless light continues to blink, continue to the next step. Step 2 Check for issues with the wireless network The following factors can cause the printer to lose the wireless connection The network connection is no longer active, or has low signal strength. The printer goes into sleep mode or standby mode. The printer is either too far away from the wireless router, or too close to it. The recommended distance between the printer and the router is meter to meters 3 ft to 5 ft. A firewall prevents the printer from accessing the computer and wireless network. A nearby device that emits radio signals such as a microwave or cordless telephone might interfere with the wireless connection. A virtual private network VPN prevents the printer from accessing the computer and wireless network. If you corrected any of the items in the list and enabled the printer to establish a connection, you can stop troubleshooting. Step 3 Connect the printer to your network Wireless light blinks, the Wireless icon is on, and the Wireless Attention icon blinks This condition occurs when the printer cannot connect to your network. Figure The Wireless light blinks, the Wireless icon is on, and the Wireless Attention icon blinks Step 1 Wait for the printer to establish a connection The Wireless light blinks slowly when attempting to connect to the wireless router or access point. Wait a few minutes, and then check the light again. If this step resolved the issue, you can stop troubleshooting. If the issue persists, continue to the next step. Step 2 Check for issues with the wireless network The following factors can cause the printer to lose the wireless connection The network connection is no longer active, or has low signal strength. The printer goes into sleep mode or standby mode. The printer is either too far away from the wireless router, or too close to it. The recommended distance between the printer and the router is meter to meters 3 ft to 5 ft. A firewall prevents the printer from accessing the computer and wireless network. A nearby device that emits radio signals such as a microwave or cordless telephone might interfere with the wireless connection. A virtual private network VPN prevents the printer from accessing the computer and wireless network. If you corrected any of the items in the list and enabled the printer to establish a connection, you can stop troubleshooting. Step 3 Connect the printer to your network 'Error A' displays The printer is silent and an A blinks on the printer control panel. The printer printed an alignment page and is waiting to scan the page and complete the alignment. Lift the scanner lid. Place the alignment page with the print side down on the right-front corner of the scanner glass, and then close the scanner lid. Position it according to the guides around the scanner glass. Figure Placing the alignment page on the scanner glass Close the scanner lid. On the control panel, press the Start Copy Color button . 'Error P' displays After installing the printheads, the printer is silent and a P blinks on the printer control panel. The printer was interrupted while priming the ink system. Press and hold the Resume button for 3 seconds to continue the priming process. For more information, go to A Blinking 'P' Error Displays. All the lights are off and the printer does not respond This condition occurs when the printer is turned off, or there is an issue with the power supply. Step 1 Turn on the printer Press the Power button to turn on the printer. If the printer does not turn on, continue to the next step. Step 2 Make sure the printer is plugged in Make sure the power cord is connected to the rear of the printer and plugged into an electrical outlet. Check the rear of the printer to make sure the power cord is inserted securely into the power connection. Check the electrical outlet to make sure the power cord is plugged in securely. Figure Check the electrical connections Rear of printer Electrical outlet Turn on the printer. If the printer does not turn on, continue to the next step. Step 3 Plug the printer directly into a wall outlet If you are using a surge protector, extension cable, or power strip, plug the printer directly into a wall outlet to make sure the power source functions correctly. Unplug the power cord from any surge protector, extension cable, or power strip. Plug the power cord directly into a wall outlet. Turn on the printer. Step 4 Make sure the electrical outlet works Make sure the electrical outlet the printer is plugged into is providing power. Unplug the power cord from the electrical outlet. Plug another appliance into the electrical outlet to make sure the outlet works. If the electrical outlet does not work, plug the printer into another outlet that does work. If the electrical outlet works, but the printer still does not turn on, continue to the next step. Step 5 Test the power with a compatible power cord from a different printer If you have another available power cord that is compatible with your printer, use the alternate cord to repeat the previous steps. If these steps resolved the issue, you can stop troubleshooting. If the printer turns on with the alternate power cord, the original power cord caused the issue. Contact HP to replace the power cord. Step 6 Service the printer If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document. One or both printhead icons, Error icon, and Printhead Alert light blink This condition occurs when one or both of the ink printheads needs attention or is faulty, incorrect, missing, damaged, or incompatible. Go to HP Customer Support, enter your printer model, and then search for Incompatible or Ink Cartridges missing error for the document on how to resolve a printhead error. Figure One printhead icon, Error icon, and Printhead Alert light blink Figure Both printhead icons, Error icon, and Printhead Alert light blink Error icon, Paper Error icon, and the Resume light are on This condition occurs when there is no paper in the input tray. Load the printer with plain paper to resolve the issue. Figure The Error icon, Paper Error icon, and the Resume light are on Raise the input tray. Slide the paper width guide all the way to the left. Load plain white paper into the input tray, slide the stack of paper down until it stops, and then slide the paper width guide against the edge of the paper. Pull out the output tray, and then raise the tray extender. note Before printing, select the correct paper size and paper type settings from the computer. HP ePrint light blinks This condition occurs when HP ePrint is turned on, but the printer is not connected to the Web Services server. Turn on Web Services, and then set up automatic printer updates to make sure your printer has the most up-to-date functionality. Periodic printer updates are required to use HP ePrint Web Services. Load plain paper in the paper tray. On the printer control panel, press the Wireless and the Information buttons at the same time. A Network Configuration Page prints. Under the General Information section, find the IP address. It is listed as URLs for Embedded Web Server. Figure Example of an IP address on the Network Configuration Page Open a new web browser window or tab. Type the IP address in your web browser's address bar, and then press Enter. The Embedded Web Server EWS opens. From the Home tab, click Web Services. Under the Web Services Settings section, click Setup, and then click Continue. Check both boxes to accept the terms of use and turn on Web Services, and then click Next. The printer searches for updates, and then automatically prints a Web Services information page. note Go to HP Customer Support, enter your printer model, and then search for Print with HP ePrint for the document on how use the ePrint service to print remotely. 'Error 1' displays and the Resume light blinks An E1 error occurs when the paper settings in the print driver do not match the paper loaded in the printer. Go to HP Customer Support, enter your printer model, and then search for Paper Mismatch for the document on how resolve the issue. 'Error 2' displays An E2 error occurs when the printer attempts to print a single-page or multi-page print job, and the paper length selected in the print settings does not match the length of the loaded paper. The printer then prints out the first page with errors. note The Error icon, Paper Error icon, and Resume light blink when a multi-page print job is attempted. You can resolve the error by canceling the print job, and then changing the print settings in the printing software. Press the Cancel button to cancel the print job or clear the error. Go to HP Customer Support, enter your printer model, and then search for Print settings guide for the document on how set the paper size in Windows and Mac. 'Error 3' displays and the Resume light blinks An E3 error occurs when there is a printer carriage jam. Figure Number of copies alternates between 'E' and '3,' and the Resume light blinks 'Error 5' displays and all lights on the control panel blink An E5 error occurs when the printer experiences a scanning error. Figure The Number of Copies icon alternates between E and 5, and all lights on the control panel blink Turn the printer off and on again to resolve a scanning error. If you were not scanning when the error occurred, skip to the Service the printer section at the end of this document. note The printer still prints even if the scan feature is unavailable. Turn off the printer. Wait at least 15 seconds. Turn on the printer. Check the lights on the control panel to make sure they no longer blink. Attempt to scan the item again. Go to HP Customer Support, enter your printer model, and then search for Scanner not found or connected for the document on how resolve connection issues. 'Error 6' displays and all the lights blink An E6 error occurs when the printer is in an error state. Figure Number of Copies icon alternates between 'E' and '6,' and all the lights blink Step 1 Reset the printer Resetting the printer can clear the error state. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source. Wait 60 seconds. Reconnect the power cord to a wall outlet and to the printer. note HP recommends plugging the printer directly into a wall outlet. Step 2 Plug the printer directly into an electrical outlet Plug the product directly into an electrical outlet to make sure that the power source functions correctly. Disconnect the power cord from the rear of the product. Unplug the power cord from any power strips or surge suppressors. Plug the power cord directly into an electrical outlet. Reconnect the power cord to the rear of the product. Press the Power button to turn on the product. Try the task again. If the issue persists, try a different electrical outlet. Step 3 Service the printer If you have completed all the previous steps and the issue persists, continue to the Service the printer section at the end of this document. 'Error 7' displays An E7 error occurs when the printer is unable to prime the system and has reached the maximum number of prime attempts. 'Error 9' displays and an Ink System Maintenance page prints An E9 error occurs when the printer detects that ink system maintenance is required. An Ink System Maintenance page prints containing instructions to open and close the printhead access door to resolve the error. note HP recommends opening and closing the printhead access door 3-4 times to remove any ink buildup and maintain the best print quality. Figure Ink System Maintenance page Service the printer Service or replace your HP product if the issue persists after completing all the preceding steps. Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area. To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.
CaraMengatasi Printer Epson L310 Lampu Tinta dan Kertas Berkedip - Ketika epson printer kesayangan kita tiba tiba tidak mau jalan dengan ditandai lampu power dan tinta berkedip kedip, mungkin saat itulah printer minta direset. Kalau benar demikian jangan keburu dibawa ke tukang servis, buang uang saja padahal kita dapat memperbaikinya sendiri.
Kliktombol "Particular adjustment mode". Gambar 3 Mengatasi Printer Epson L300/L310 yang Berkedip. Lalu cari bagian Maintenance dan pilih Waste ink pad counter, Lalu Ok. Gambar 4 Mengatasi Printer Epson L300/L310 yang Berkedip. Centang kolom Main pad counter, klik tombol Check tunggu sampai point dan persentasenya muncul kemudian klik tombol
Lepaskanlahtombol power yang anda tekan ketika anda selesai memasang kabel power pada printer anda. Untuk menyalakan printer anda, tekan kembali tombol power anda. Jika karena terputus arus listrik tiba-tiba, maka cara ini akan ampuh untuk mengatasi lampu berkedip. Jika lampu printer kembali berkedip setelah printer putus arus listrik, ulangi langkah di atas kembali.
20 Tv LED LG 32" Model 32LF520A-TA lampu power kedap kedip Kerusakan: LED LG dengan kerusakan awal led dihidupkan keluar lampu stand by, kontrol panel berikut remot tidak berfungsi sama sekali. Ketika diperhatikan lampu stand by berkedip secara teratur memandangkan kata si empunya ini LED kena petir.
BeliLampu Kota Kedap Kedip Harga Promo & Terbaru April 2022 - Dapatkan Harga Lampu Kota Kedap Kedip Termurah Di Blibli! Promo & Diskon Murah ⚡100% Original 15 Hari Retur ⌛ Pengiriman Cepat Gratis Ongkir
6nrw9c. r55qx235ht.pages.dev/898r55qx235ht.pages.dev/841r55qx235ht.pages.dev/788r55qx235ht.pages.dev/139r55qx235ht.pages.dev/697r55qx235ht.pages.dev/313r55qx235ht.pages.dev/828r55qx235ht.pages.dev/2r55qx235ht.pages.dev/585r55qx235ht.pages.dev/515r55qx235ht.pages.dev/844r55qx235ht.pages.dev/691r55qx235ht.pages.dev/994r55qx235ht.pages.dev/862r55qx235ht.pages.dev/853
printer hp lampu power kedap kedip
